PROGRAMMING GUIDE Part No. : MUL-53221-07
Start of Configuration SEND COMMAND IN BLOCK MODE COMMUNICATION You can use this option to set your own “Send” command used in block mode communic
INTERFACE CONFIGURATION 14 Start of Configuration 1. RS-232C SERIAL COMMUNICATION PARAMETERS SETTING The RS-232C scan
Start of Configuration ACK/NAK RESPONSE TIME SETTING (Cont’d) 3 sec 1 sec 5 sec BAUD RATE 19200 9600 4800 2400 1200 600 16 DATA B
Start of Configuration MESSAGE TERMINATOR (FOR RS-232C TYPE ONLY) None CR/LF CR LF H Tab STX/ETX EOT 18 2. KEYBOARD EMULAT
Start of Configuration KEYBOARD TYPE SELECTION (Cont’d) NEC 9801 IBM 3196 Terminal APPLE MAC II(※) IBM 3477/3472 Terminal PS2/30/56 IBM
Start of Configuration MESSAGE TERMINATOR (FOR KEYBOARD WEDGE USE) None Return /Enter Hor. TAB Execute KEYBOARD TYPE SELECTION Scan Code
Start of Configuration 00H~1FH ASCII Code defined Alt-mode code Crtl+code 3. WAND EMULATION PARAMETERS SETTING EMULATION SPEED SELECTION
Start of Configuration 4. USB INTERFACE PARAMETERS SETTING The USB mode is effectively a keyboard emulator that works with hosts that USB-compatib
Start of Configuration READING CODE SELECTION Code 39 Enable Code 39 Disable Coda bar Enable Coda bar Disable UPC/ EAN/ JAN Enable UPC/ EAN
Start of Configuration READING CODE SELECTION (Cont’d) Italian Pharmacy Enable Italian Pharmacy Disable CODE 39 PARAMETERS SETTING CHARACTE
PROGRAMMING GUIDE for BARCODE SCANNERS The guide can be used as keyboard emulation, RS- 232C serial i
Start of Configuration CHECK DIGIT NO Calculate and Transmit Calculate but not Transmit CHINESE POST CODE PARAMETERS SETTING LENGTH MAX
Start of Configuration UPC/EAN/JAN PARAMETERS SETTING (Cont’d) EAN-13 EAN-8 ADDENDUM NO 5 Characters 2 Characters 2 or 5 Characters F
Start of Configuration TRANSMIT UPC-E CHECK DIGIT Yes No TRANSMIT EAN-13 CHECK DIGIT Yes No TRANSMIT EAN-8 CHECK DIGIT Yes No
MSI/P Start of Configuration CODE 128 PARAMETERS SETTING (Cont’d) CHECK DIGIT No Calculate but not Transmit Calculate and Transmit UCC/EAN1
Start of Configuration MSI/PLESSY PARAMETERS SETTING (Cont’d) PLESSY CODE SETTING Calculated and transmitted Calculate but not transmitted CHE
Start of Configuration ISBN/ ISSN CONVERSION The function convents the UPC/EAN codes appearing on books and magazine not ISBN/ISSN format. ACTIVE
Start of Configuration HEADER AND TRAILER This option allows you to append a header and/or a trailer to every message transmitted via the serial po
Start of Configuration BARCODE IDENTIFIER CODE SETTING (Cont’d) Codabar Code 39 Code 128 Code 93 MSI MATRIX 25 Set 46 Trun
APPENDIXES 48 APPENDIX A CODE 39 FULL ASCII CODE TABLE ASCIICODE 39 VALEUR HEXA.ASCII CODE 39 VALEUR HEXA. NUL %U 00 % /E 25S
CODE 39 FULL ASCII CODE TABLE ASCII CODE 39 VALEUR HEXA. ASCIICODE 39 VALEUR HEXA.J J 4A e +E 65K K 4B f +F 66L L 4C g +G 6
IMPORTANT NOTICE This is a general guide for varies scanners, and not all functions will perform in every scanners. Other than specified in this
CODE 39 FULL ASCII BARCODE TABLE Start of Configuration NUL ENQ (Up) SOH (Ins) ACK (D n) ow STX (Del) BEL (L t) ef ETX (Home) BS
APPENDIX B CODE 39 FULL A CII BARCODE TABLE S St ation art of Configur SYN (F6) GS (ESC) ETB (F7) RS Ctl (L) CAN (F8) US Alt (L) EM (F9)
APPENDIX B CODE 39 FULL A CII BARCODE TABLE S Start of Configuration 2 : 3 ; 4 < 5 = 6 > 7 ? 8 @ 9 A 56 APPENDI
APPENDIX B CODE 39 FULL A CII BARCODE TABLE S Start of Config ration u P W Q X R Y S Z T [ U \ V ] APPENDIX B CODE 39 FU
APPENDIX B CODE 39 FULL A CII BARCODE TABLE S Start of Configu tion ra l s m t n u o v p w q x r y 60 APPENDIX B CODE 3
BARCODE SAMPLES Code 39 CODE 3 9 Code 128 CODE 1 2 8 Interleaved 2 of 5 1234567890 Coda bar(NW-7) A$99.95A UPC A 0 44252 30245 1 EAN-13 4 7
Chinese Post Code Parameters Setting ... 32 UPC/ EAN/ JAN Parameters Setting ... 33 Coda bar/ Monarch Parameters Setting ...
3. DEFAULT PARAMETERS This table gives the default settings of all the programmable parameters. The default settings will be restored whenever the
DEFAULT VALUES OF DECODING PARAMETERS Function Code Default Value Code 39 Enable ITF 2 of 5 Enable Chinese Post Code Disable UPC/EAN/JAN En
SYSTEM SETTING 6 Start of Configuration RESET y The reading of the "RESET” label turns all the pa
GENERAL CONFIGURATION 8 Start of Configuration SCANNING MODE SELECTION (for laser scanner) For series laser scanners, the
Start of Configuration DATA REDUNDANT CHECK The option allows you to set decoder data redundant check. Enable Disable INTER-MESSAGE DELAY The
Kommentare zu diesen Handbüchern